0

Lowes Laminate Flooring Installation

Lowes Laminate Flooring Installation

Install a Laminate Floor Laminate floors have the same great look as hardwood floors. The following step-by-step instructions will show you how to install a floating (without adhesive, nails or staples) laminate floor. Save Item Send to a FriendPrint Tools & Materials Tools Jigsaw Circular Saw Table Saw (optional) Miter Saw (optional) Tapping Block Hammer Nail Set Dead Blow Hammer Pull Bar Utility Knife Tape Measure Level Safety Glasses Dust Mask Knee Pads Materials Laminate Flooring Underlayment (if required) Moisture / Vapor Barrier (if required) Wood Glue Flooring Spacers Transitions and Mouldings Finish Nails Wood Filler Silicone Sealant (if required) Product costs, availability and item numbers may vary online or by market. Missing anything? Shop Online Instructions Interlocking laminate floating floors can be installed over clean and level ceramic, vinyl, concrete or plywood / OSB subflooring. Typically, laminate flooring cannot be installed in rooms with a floor drain. Make sure you follow all local building codes when installing flooring. CautionWear safety glasses when cutting the laminate pieces. Good to KnowFor comfort and safety, use knee pads, a soft pad or a towel under your knees when installing flooring. Preparation Step 1 Read the manufacturer’s instructions before the installation. In addition to installation steps, you’ll find information on different types of subfloors and moisture tests. The steps below describe laminate flooring installation, but always follow the instructions for your specific flooring. Step 2 Prepare the subfloor. Refer to the article and video on how to prepare a wood subfloor or the video on how to prepare a concrete subfloor. They’ll show you how to level your floor and establish an installation guideline. Step 3 If required by the manufacturer, install an underlayment or and / or a moisture barrier, making sure that the top surface side is installed as recommended. Many laminate floors have the underlayment pre-attached to the underside. CautionIf you are installing laminate flooring over a concrete subfloor, a moisture barrier is required. Step 4 Place the flooring materials in the installation room for at least 72 hours prior to installing them so they can acclimate to the temperature and humidity ranges recommended by the manufacturer. Installing the First Rows Step 1 When installing the flooring, assemble the pieces in the order shown in the diagram. Step 2 Loosely lay the first row with the tongue of the boards facing the starting wall. Step 3 To prep the planks in row one, cut the tongue off the long side of all of the pieces. Using a table saw makes the tongue removal easy. Just set the fence at the appropriate width and cut the boards. Step 4 Place spacers between the laminate planks and adjacent walls for the manufacturer’s recommended expansion gap. Most manufacturers call for an expansion gap of 1/4 of an inch. Step 5 Begin piecing the first few rows of laminate boards about 2 feet away from the starting wall. Work from left to right. Assembling the first few rows away from the starting wall gives you extra room to work. Once the first few rows have been assembled, you can carefully slide the flooring into its final position. Step 6 Cut the first piece of row two, following the manufacturer’s instructions for staggering the joints between rows. Typically, at least a 12-inch stagger is recommended. Staggering the seams at each row strengthens the floor and enhances its appearance by giving it a more random pattern. To cut the flooring, lay the board on its face (bottom up) and cut with a saw equipped with a fine-tooth blade for flooring. Step 7 Insert the tongue of the long side of row two into the groove of the first plank of row one. You may have to use a slight angle to set the tongue in the groove. Just press the board down until it locks in place. Step 8 Attach the next piece of row one. Once again, insert the tongue at a slight angle into the groove and press down to lock it. Make sure the planks are aligned and the surface is even at the joints. Step 9 Add the next piece of row two. Insert the tongue into the long side of row one, slide the piece toward the end joint, then press down to lock the joint. This locking method should be used for the rest of the installation. Step 10 After you’ve installed the first two planks of each row, place a weight, like a toolbox or a carton of flooring, on top of the first planks to hold each row in place. Step 11 Continue installing the first two rows, locking a plank for row one, then a plank for row two. Use this pattern to finish the rows. Trim the last piece to allow for spacers and the expansion gap if required. Step 12 A tapping block may be needed when a plank can’t be rotated, such as under a doorframe. Position the board as close as possible to its finished location under the doorframe. Follow the manufacturer’s instructions for using the tapping block. Typically, you position it along the groove side of the plank, then use a dead blow hammer to tap the plank into place, locking the joint. Step 13 Once the first two rows are assembled, slide them into position against the starting wall. Be sure to maintain the manufacturer’s recommended expansion gap with flooring spacers. Installing the Rest of the Floor Step 1 Continue installing the laminate flooring, staggering the joints at least 12 inches and maintaining the expansion gap. Good to Know Use cut pieces to start rows, making sure the joints are staggered properly. Step 2 When laying the flooring around obstructions, like floor vents, cabinets or columns, cut the flooring to fit with a jigsaw. To install the flooring around pipes, you may need to use a jigsaw and wood glue to make the planks fit properly. Cut a notch in the flooring to fit around the pipe. With the smaller excess piece, cut it to fit on the other side of the pipe. Set the smaller piece in place and attach it to the larger plank with wood glue along the cut line(s). Step 3 Check the manufacturer’s instructions for applying silicone sealant in areas with high moisture levels, such as a bathroom, laundry room or kitchen. Excess moisture under the planks can damage the flooring. When installing around a bathtub or sink, apply silicone sealant to create a watertight seal. You’ll need to take some special steps when installing around a toilet. See Replace a Toilet for more instructions on removing and installing a toilet. Remove the toilet. Cut the flooring to fit around the drain. Remember to account for the manufacturer’s required expansion gap. Install the flooring. Apply silicone sealant in the expansion gap. Allow sealant to dry, then reinstall the toilet. Also check the manufacturer’s instructions for applying sealant along kitchen cabinets that house a dishwasher or refrigerator. Step 4 For the last row, you may have to cut the pieces to fit. Measure the width needed for the last row and subtract the manufacturer’s expansion gap. Measure to the board surfaces (excluding the tongue) and rip (cut lengthwise) the last boards along the groove edge. Some flooring products have a small plastic tongue in the short side groove of the planks which helps lock the pieces together. Be sure to remove the plastic tongue before cutting the length of the board. Step 5 Use a pull bar and hammer to lock the last row in place. Finishing Up Step 1 Install transition strips at entries and where the floor meets other types of flooring, following manufacturer’s instructions. Step 2 Remove the wall spacers once the transitions are in place. Step 3 If you installed a separate underlayment, cut the excess. Step 4 When installing in a bathroom, kitchen, laundry room or along an exterior door, apply silicone sealant in the expansion space around the perimeter of the floor. This should be done once the entire floor is in place. Step 5 Install the baseboards and shoe moulding to the walls as needed. Attach the trim and shoe moulding to the walls. Do not attach them to the flooring. Step 6 Keep one or two cartons of your laminate flooring so you can fix any potential problems in the future, like a damaged board. Related Articles Laminate Floor Buying Guide How to Choose an Area Rug 10 Questions to Ask Before Buying a New Floor Shop Lowe’s Laminate Flooring Area Rugs Related Videos & Guides Install an Engineered Hardwood Floor How to Prep a Plywood Subfloor Ideas & Inspiration Display Table Learn How to Create and Hang a Gallery Wall Lowe’s Services Laminate Flooring Install
lowes laminate flooring installation 1

Lowes Laminate Flooring Installation

Tools & Materials Tools Jigsaw Circular Saw Table Saw (optional) Miter Saw (optional) Tapping Block Hammer Nail Set Dead Blow Hammer Pull Bar Utility Knife Tape Measure Level Safety Glasses Dust Mask Knee Pads Materials Laminate Flooring Underlayment (if required) Moisture / Vapor Barrier (if required) Wood Glue Flooring Spacers Transitions and Mouldings Finish Nails Wood Filler Silicone Sealant (if required) Product costs, availability and item numbers may vary online or by market. Missing anything? Shop Online Instructions Interlocking laminate floating floors can be installed over clean and level ceramic, vinyl, concrete or plywood / OSB subflooring. Typically, laminate flooring cannot be installed in rooms with a floor drain. Make sure you follow all local building codes when installing flooring. CautionWear safety glasses when cutting the laminate pieces. Good to KnowFor comfort and safety, use knee pads, a soft pad or a towel under your knees when installing flooring. Preparation Step 1 Read the manufacturer’s instructions before the installation. In addition to installation steps, you’ll find information on different types of subfloors and moisture tests. The steps below describe laminate flooring installation, but always follow the instructions for your specific flooring. Step 2 Prepare the subfloor. Refer to the article and video on how to prepare a wood subfloor or the video on how to prepare a concrete subfloor. They’ll show you how to level your floor and establish an installation guideline. Step 3 If required by the manufacturer, install an underlayment or and / or a moisture barrier, making sure that the top surface side is installed as recommended. Many laminate floors have the underlayment pre-attached to the underside. CautionIf you are installing laminate flooring over a concrete subfloor, a moisture barrier is required. Step 4 Place the flooring materials in the installation room for at least 72 hours prior to installing them so they can acclimate to the temperature and humidity ranges recommended by the manufacturer. Installing the First Rows Step 1 When installing the flooring, assemble the pieces in the order shown in the diagram. Step 2 Loosely lay the first row with the tongue of the boards facing the starting wall. Step 3 To prep the planks in row one, cut the tongue off the long side of all of the pieces. Using a table saw makes the tongue removal easy. Just set the fence at the appropriate width and cut the boards. Step 4 Place spacers between the laminate planks and adjacent walls for the manufacturer’s recommended expansion gap. Most manufacturers call for an expansion gap of 1/4 of an inch. Step 5 Begin piecing the first few rows of laminate boards about 2 feet away from the starting wall. Work from left to right. Assembling the first few rows away from the starting wall gives you extra room to work. Once the first few rows have been assembled, you can carefully slide the flooring into its final position. Step 6 Cut the first piece of row two, following the manufacturer’s instructions for staggering the joints between rows. Typically, at least a 12-inch stagger is recommended. Staggering the seams at each row strengthens the floor and enhances its appearance by giving it a more random pattern. To cut the flooring, lay the board on its face (bottom up) and cut with a saw equipped with a fine-tooth blade for flooring. Step 7 Insert the tongue of the long side of row two into the groove of the first plank of row one. You may have to use a slight angle to set the tongue in the groove. Just press the board down until it locks in place. Step 8 Attach the next piece of row one. Once again, insert the tongue at a slight angle into the groove and press down to lock it. Make sure the planks are aligned and the surface is even at the joints. Step 9 Add the next piece of row two. Insert the tongue into the long side of row one, slide the piece toward the end joint, then press down to lock the joint. This locking method should be used for the rest of the installation. Step 10 After you’ve installed the first two planks of each row, place a weight, like a toolbox or a carton of flooring, on top of the first planks to hold each row in place. Step 11 Continue installing the first two rows, locking a plank for row one, then a plank for row two. Use this pattern to finish the rows. Trim the last piece to allow for spacers and the expansion gap if required. Step 12 A tapping block may be needed when a plank can’t be rotated, such as under a doorframe. Position the board as close as possible to its finished location under the doorframe. Follow the manufacturer’s instructions for using the tapping block. Typically, you position it along the groove side of the plank, then use a dead blow hammer to tap the plank into place, locking the joint. Step 13 Once the first two rows are assembled, slide them into position against the starting wall. Be sure to maintain the manufacturer’s recommended expansion gap with flooring spacers. Installing the Rest of the Floor Step 1 Continue installing the laminate flooring, staggering the joints at least 12 inches and maintaining the expansion gap. Good to Know Use cut pieces to start rows, making sure the joints are staggered properly. Step 2 When laying the flooring around obstructions, like floor vents, cabinets or columns, cut the flooring to fit with a jigsaw. To install the flooring around pipes, you may need to use a jigsaw and wood glue to make the planks fit properly. Cut a notch in the flooring to fit around the pipe. With the smaller excess piece, cut it to fit on the other side of the pipe. Set the smaller piece in place and attach it to the larger plank with wood glue along the cut line(s). Step 3 Check the manufacturer’s instructions for applying silicone sealant in areas with high moisture levels, such as a bathroom, laundry room or kitchen. Excess moisture under the planks can damage the flooring. When installing around a bathtub or sink, apply silicone sealant to create a watertight seal. You’ll need to take some special steps when installing around a toilet. See Replace a Toilet for more instructions on removing and installing a toilet. Remove the toilet. Cut the flooring to fit around the drain. Remember to account for the manufacturer’s required expansion gap. Install the flooring. Apply silicone sealant in the expansion gap. Allow sealant to dry, then reinstall the toilet. Also check the manufacturer’s instructions for applying sealant along kitchen cabinets that house a dishwasher or refrigerator. Step 4 For the last row, you may have to cut the pieces to fit. Measure the width needed for the last row and subtract the manufacturer’s expansion gap. Measure to the board surfaces (excluding the tongue) and rip (cut lengthwise) the last boards along the groove edge. Some flooring products have a small plastic tongue in the short side groove of the planks which helps lock the pieces together. Be sure to remove the plastic tongue before cutting the length of the board. Step 5 Use a pull bar and hammer to lock the last row in place. Finishing Up Step 1 Install transition strips at entries and where the floor meets other types of flooring, following manufacturer’s instructions. Step 2 Remove the wall spacers once the transitions are in place. Step 3 If you installed a separate underlayment, cut the excess. Step 4 When installing in a bathroom, kitchen, laundry room or along an exterior door, apply silicone sealant in the expansion space around the perimeter of the floor. This should be done once the entire floor is in place. Step 5 Install the baseboards and shoe moulding to the walls as needed. Attach the trim and shoe moulding to the walls. Do not attach them to the flooring. Step 6 Keep one or two cartons of your laminate flooring so you can fix any potential problems in the future, like a damaged board.

Lowes Laminate Flooring Installation

Lowes Laminate Flooring Installation
Lowes Laminate Flooring Installation
Lowes Laminate Flooring Installation
Lowes Laminate Flooring Installation
Lowes Laminate Flooring Installation

You can download all 1 of Lowes Laminate Flooring Installation photo to your gadget by right clicking photo and then save image as. Do not forget to share if you interest with this photo.